Customized wardrobe installation should not be considered very simple, today the website will come to share with you the custom wardrobe installation strategy and custom wardrobe installation precautions. First, the preparation stage 1, the material is on the scene More formal furniture manufacturers, cardboard packaging is generally shipped to the site. After unpacking, check the plates and hardware. 2, fixing screws The nails are generally left on the plates according to the design drawings, and the workers at the site use special tools to fix the screws. 3, measuring the side panels Since the closet is placed against the wall, the side panel is sawn off at the position of the baseboard. After you have it, look it up and see if it fits. Second, the installation phase 1. Place the bottom plate The floor placed on the bottom of the wardrobe should be cleaned beforehand, because it will be very troublesome to clean up after installation. 2, fixed frame Install the side and back panels of the closet according to the grooves on the board and adjust the position between the boards. 3, install the top plate It is best to prepare a climbing stool on the scene. The top plate should be lifted up and then fixed with rivets. 4, the installation shelf Place the shelf where you have previously screwed it and then secure it. Pay attention to the fixed position of the shelf and the back and side panels. Third, the closing stage 1, install the door leaf The two sliding doors should be attached to the position of the guide rails. Fix the door leaf first and then fix the guide rails at the bottom side to avoid the phenomenon that the door leaf falls off in the future. 2, adjustment and improvement After all the installations are completed, make a "full inspection" of the wardrobe. If there is any deviation, adjust it in time. Fourth, the completion of acceptance Finally, check the wardrobe: Shake the cabinet to see if it is firm and the details are in place. Custom wardrobe installation notes: Installation Note 1: Check the materials After the wardrobe door with mirror door material is transported to the site, all materials should be inspected, meet the design requirements, check whether the size of the mirror door is correct, the diagonal deviation should not be greater than 1mm, and the door clamp, floor spring and handle specifications are correct. Whether the accessories are complete, after inspection, should be stored in a safe place, properly preserved, and covered for protection. Installation Note 2: Punch positioning and installation of the door clamp When installing the door clamp, use the door clamp to accurately mark the installation position line and the punching position on the mirror with the door and carefully remove the excess part with the pliers. Then drill the hole with the hand drill and the 18 mirror drill bit. Punching should be carried out gently and swayingly. It should be added with water. Do not press down when it is fast, so that it will naturally fall through, so that the perforated part has a mirror surface intact. Installation Note 3: Install the door leaf Remove the door clamp (F20) pre-installed on the door leaf and place the door leaf on the ground spring (use the plywood in the wardrobe with the mirror door and the mirror frame or other door frame to protect the mirror door and its door frame) Not damaged.), and on the same plane with two borders or mirrors, after the door leaf is placed, insert the F30?F40 upper door clamp shaft into the F20 upper door clamp sleeve, and reinstall the upper door clamp F20 on the mirrored door leaf. After the installation is completed, the adjustment is made. The switch is flexible. After the adjustment, the mirror rubber with the door clamp and the small wooden wedge with the mirror knife are cut flat than the upper end of the lower door clamp, and the glue should not be protruded outside the door clamp, and Clean and re-glue for modification. Installation Note 4: Measuring distance and mounting handle The handle between the handle and the mirror door is 120~150mm, and the installed door handle ensures symmetrical, vertical and firm. Installation Note 5: Wardrobe Cleaning After installation, use the mirror cleaning agent to clean the stain on the mirror door of the wardrobe to ensure the cleanliness of the wardrobe door. Electric Nose Hair Trimmer,2 In 1 Eyebrow Hair Trimmer,Protable Nose Hair Trimmer,3 In One Trimming Hair ZHEJIANG SHENGFA ELECTRIC APPLIAMNCES CO.,LTD , https://www.shengfa-appliance.com
Customized wardrobe installation guide custom wardrobe installation precautions