After the computer is used for a long time, it will inevitably cause some problems. For example, the computer is infected with the stubborn virus Trojan, the debris in the hard disk is more and more, the running speed is slower and slower, the system can not be used, and the system often crashes. At this time, if you can't find a specific reason, the best way is to reinstall the system. So how does the computer reinstall the system ? The following decoration home decoration network Xiaobian will bring you four common computer reinstallation system steps for your reference. How does the computer reinstall the system? Computer reinstallation system steps 1, U disk installation method: The first step is to double-click UltraISO.exe and open the downloaded system file. The second step is to insert a USB flash drive or a memory card and select "Start Disc - Write Hard Disk Image"; The third step is to select the write mode and make a boot disk (back up important data before writing). There are two modes: USB-ZIP and USB-HDD. There are different modes supported by the motherboard. In most cases, USB-ZIP is supported. A dialog box will pop up, select "Yes" to continue writing data; The fourth step, after the production is completed, you can start to install the system. Insert the USB flash drive into the netbook and turn it on. Press DEL (or F2) to enter the motherboard CMOS settings when booting, and set the first boot device to be USB or removable device. The fifth step, start with U disk, enter WINPE, the new book must be partitioned first, then double-click the "automatic installation system" in the lower left corner of the desktop; In the sixth step, press any key to start copying the system. After copying, the system will restart automatically. After the restart, the system will automatically deploy and install, including common software and hardware drivers will be automatically installed. Computer reinstallation system step 2, CD installation method: The first step is to buy a system disk first, or if you have the conditions, you should burn one (you need to buy a good empty disk, find a good system image on the Internet, the file format. ISO), in view of The system disk sold for a few dollars on the market is of poor quality, the number of times used is too high or the disk drive is prone to read errors after aging, and some files cannot be installed. The second step is to set the CD-ROM drive to start. Different motherboards enter the BIOS settings in a slightly different way. IBM notebooks are powered by pressing the [Access] button. Some computers are powered on and press the [Del] button. Some are powered on and press the [F12] button. Generally, there are prompts when booting. The third step, after setting [CD-ROM] to start, press [F10] to save and exit. If the prompt “boot from cd please press anykey...†appears, just press a button and you can enter the installation. Everyone knows that the system needs to be installed on the C drive. After the carriage return, you are prompted to format it or format it. After formatting, you can start the installation. When you click [Next], you can click twice, and you don't need to set anything else. The fourth step, after installing the windows, remove the CD and install the driver. Computer reinstallation system step 3, PE system installation The first step is to download a system image from the existing Windows system. The file name suffix is ​​.ISO. Then download a general-purpose PE and install it on a disk other than the system. For example, if Windows is installed on the C drive, install the PE on any disk in D/E/F.... After installing the downloaded PE, restart the computer. The second step, after rebooting, choose to enter the PE system. After entering, do not operate, go directly to [My Computer], right click C drive - click [Format] - then close [My Computer] - click [Start 】format. The third step, click [Start] - [Programs], find the virtual drivemanager (the rain forest wood wind called VDM virtual drive), click [Load], find the downloaded system image double-click. Then, open [My Computer] and find that there is a virtual CD-ROM named after the system image we downloaded. Double-click to open, find setup.exe, double-click to run and enter the installation. Computer reinstallation system step 4, DOS system installation DOS system installation is very simple, complicated how to start the DOS system. Now there are many DOS toolboxes on the Internet (such as Dwarf DOS Toolbox, MaxDOS Toolbox, etc.), which can be installed on the hard disk in Windows system. It is possible to choose whether to enter Windows or DOS system. After entering the DOS system, switch the drive letter to the folder where the downloaded system image is located. For example, the system image is placed in the folder named "WIN" on the D drive. The steps in this step are: first enter the command D:, then press Enter, the drive letter is D:/>, then enter cdwin, the drive letter is D: / WIN>, then enter winnt, enter, The installation started. The above is how the computer brought to you by Xiaobian is how to reinstall the system? The entire contents of the computer reinstallation system steps, I believe that everyone after reading this article has a basic understanding of how to reinstall the computer system, if you want to know more about the decoration consultation, please click to enter the decoration knowledge channel. More related wonderful reading: How to look at the computer configuration? The latest assembled computer configuration recommended What is the reason for the computer crash? What should I do if the computer freezes? Why is the computer blue screen? How to solve computer blue screen? Why can't the computer be turned on? What if the computer can't open the machine? What if the computer audio has no sound? what is the reason?
Artificial grass yarn provide the look and feel of an artificial grass surface and are an important part of a sports system to help ensure it meets various performance characteristics. The quality of synthetic turf fiber is therefore essential for a quality surface. Technical details such as microns, dtex, shape, colour or polymer grade do not, by themselves, determine the overall quality of the turf fiber, but the ability to design optimal synthetic grass fiber in combination with advanced extrusion technology is what determines the quality of the yarns.
Artificial Grass Yarn,Artificial Grass Sand Infill,Sand For Astroturf,Artificial Turf Filler JIANGSU WMGRASS CO., LTD. , https://www.wmgrasslawns.com
How does the computer reinstall the system? Computer reinstallation system steps