(This article is an original article from Bisheng. It is forbidden to reprint, and reprinting must be corrected) Error message 1. Loading error: This error message is usually displayed after loading or cutting the film, indicating that there is an error loading the machine. If it appears when the film is loaded after replacing the film, you can try to feed the film forward by hand, and then execute the film loading command. Generally, this error may be caused by damage to the motor or clutch, or loosening the clamping screw on the motor. 2. FAN trouble 1 and FAN trouble 2: This information indicates that the fan of the imagesetter has problems and generally needs to be replaced. FAN 1 is the lower fan, FAN 2 is the upper fan. 3. Download error 1: This message will appear only when the main version is downloaded. Generally, it is not recommended that users do the download work by themselves. Operation errors will cause chip damage on the main version. 4. Mode unmatch: This information indicates that the settings on the main version do not match the system data. In the case where the user does not modify the jumper switch on the main version without permission, this error generally does not occur. When it is found that this error is displayed, it is recommended to contact professional maintenance personnel for repair. 5. Flim jam 1 (a) and Flim jam 2 (a): This is the machine display card. The information of both cards is that the machine's next sensor does not detect the film. There are many reasons for the occurrence of these two kinds of cards, such as: the broken film sensor is damaged or not in the correct position, the cutting system has a problem, the main roller or the driving roller has a problem, the main board or the OPTV board has a problem, etc. One-step inspection and elimination. It should be reminded here that when removing the stuck film, do not use strong force to pull it out. Pay attention to where the film is stuck and cannot be pulled out, and then carefully remove it, otherwise it may cause misalignment of other sensors or some motor Was burnt down. Generally, when these two kinds of cards are taken out, you can use a machine cutter (when there is no problem with the cutter) to cut the film, so that the film can be divided into two sections and taken out. 6. Flim jam 3 (a): This card error phenomenon will only appear on the machine that uses the receiver. It may be that there is a problem with the receiver connection, or there are remaining films in the receiver, or the sensor is damaged or the location is not good. , Or the main version is damaged, you can first check whether there is any film in the receiver. 7. Flim jam 10 (a): This card error phenomenon will only appear on the machine connected to the line punching machine. The solution is the same as the solution of Flim jam 1 (a) and Flim jam 2 (a). 8. Flim jam 11 (a): This card phenomenon only exists on the machine connected to the film processor. When the film starts to be transferred to the film machine, the film sensor of the phototypesetting machine after 65 seconds still detects the film Exists, then the machine will report this error. 9. Flim jam 12 (a): This message will only appear on the machine connected to the film punching machine. After the lower film motor starts to rotate, the film sensor is still not turned on after 8 seconds. , The machine will show this error message. When this error message appears, the user should check whether the ground wire of the two machines is normal, clear the fee in the sub-receiver, and then put the sub-receiver back in place. 10. Flim jam 13 (a): This message will only appear on the machine connected to the film processor. When the cut film is sent to the film machine, the photo sensor of the photo-composing machine has been released after 180 minutes. Off (no film), the film sensor is still on. Generally, when this error message appears, there is a problem with the adjustment of the parameters of the punching machine, and it needs to be checked and corrected. 11. Flim jam 14 (a): This error message appears during the process of cutting the film into the punching machine. Within 2 seconds after the AT door is opened, the punching sensor is still off. After this message appears, the user can check whether the imagesetter and the processor are properly connected and the position is appropriate. If the problem persists after reconnecting, check if the AT door is working properly. The motor may be broken or the connection between the motor and the door may be loose. 12. Flim jam 2 (d) and Flim jam 2 (b): These two error messages only appear on machines using the folder mode. It will appear in the following situations: the film receiver is not placed properly, the rear buffer guide roller is not placed properly, the sensor of the rear buffer guide roller is displaced or damaged, and there is a problem with the motherboard. 13. Machine error 3: This message indicates that there is a problem with the cutting system, which may be a problem with the cutting system or the motherboard. 14. Machine error 5: This message indicates that there is a problem during the closing process of the tailgate. If this kind of error occurs, check the sensor of the rear baffle, control the motor, insurance and main board of the rear baffle. 15. Machine error 6: This message indicates that there is a problem when the front baffle is closed. The sensor of the front baffle should be checked to control the motor, insurance and main board of the front baffle. 16. Machine error 7: When the pressure roller is raised, a failure occurs, and the machine will display this error message. Generally, the pressure roller position sensor is damaged or the position is not good, the pressure roller motor is damaged, the connection screw between the pressure roller motor and the roller is loose, and there is a problem with the insurance or the main board. 17. Machine error 9: This error message will appear when there is a problem with the filter inside the machine. You need to check the position detection sensor, insurance, motor, and motherboard of the filter. 18. Machine error 11: This message indicates that a fault occurred when the AT door was closed. It is necessary to check the sensor, motor, insurance, and main board of the AT door. 19. Machine error 12 and Machine error 15: These two messages indicate that the exposure failed. Generally, you need to check whether the light intensity detection sensor is dirty, whether the voltage on the OPTV version is too low, and whether the laser is damaged. 20. Machine error 16: This error message indicates a problem with the transfer mirror of the imagesetter. Generally, you should check whether the rotating mirror is not installed or damaged, whether the driving motor of the rotating mirror is damaged, and whether there is a problem with the motherboard and the power supply. twenty one. Data write error: This message shows a problem when writing system data. This message usually appears when the system data or display language is modified. If this message appears, contact the manufacturer to replace the EPROM. twenty two. Film jam 2 (c): This card information appears on the machine using the receiver mode. In A mode, the sensor does not reach the back buffer sensor within 10 seconds after cutting, this error message will appear At this time, you should check whether the receiving clip is installed, whether the rear buffer roller is installed, whether there are any remaining films in the receiving clip that have not been removed, whether the rear buffer sensor is damaged, and whether there is a problem with the motherboard. twenty three. Film jam 2 (e): This message indicates that the film is stuck in the position of the receiver. You need to check whether the receiver is installed, whether the sensor of the receiver is damaged and the condition of the motherboard. twenty four. Machine error 19: This message shows that the machine has a problem during the opening of the rear bumper. If this kind of error occurs, check the sensor of the rear baffle, control the motor, insurance and main board of the rear baffle. 25. Machine error 20: This message indicates that there is a problem when the front baffle is opened. The sensor of the front baffle should be checked to control the motor, insurance and main board of the front baffle. 26. Machine error 21: When the pressing roller falls down, the machine will display this error message. Generally, the pressure roller position sensor is damaged or the position is not good, the pressure roller motor is damaged, the connection screw between the pressure roller motor and the roller is loose, and there is a problem with the insurance or the main board. 27. Machine error 23: This message indicates that a fault occurred when the AT door was opened. You need to check the sensor, motor, fuse, and main board of the AT door. 28. Machine error 24: This message appears when there is a problem with the front bezel, usually the sensor is damaged or there is a problem with the motherboard. 29. Machine error 25: This information is also related to the front bezel. Check the sensor and main board of the front bezel. 30. Machine error 26: This message will only appear on the machine equipped with a punching device, prompting the user that the punching device is faulty, you should check the sensor position of the punching device and whether it is damaged, and whether the motor of the punching device works normally , Whether the insurance and main board are damaged. 31. Machine error 27: This message will only appear on the machine equipped with the punching device, which prompts the user that the sensor working status of the punching device has a problem. 32. I / F error 1: This error message indicates that SCSI has a problem during data transmission, and you need to restart the machine. 33. Serial error: This information indicates that there is a problem with the data transmission inside the machine. Check the SCON board and the connection on it. 34. Setting error 1: The position of the jumper on the SCON board is incorrect and needs to be corrected. 35. Setting error 2: This message indicates that a payroll connection on the SCON board is incorrect. 36. Image error: This message usually appears during the exposure process. If this error message frequently appears on the machine, it indicates that the hard disk of the imagesetter needs to be replaced. When the machine is working in a state without a hard disk, this information is also caused, because the file transmission speed is different from the exposure speed of the imagesetter, it is recommended that the user not use the state without a hard disk. 37. Disk 1 crash and Disk 2 crash, Disk 1 error and Disk 2 error, Disk 1 Re-format and Disk 2 Re-format, Disk 1 Bus error and Disk 2 Bus error, Disk 1 Unmounted and Disk 2 Unmounted: These information are all Prompt a problem with the hard disk inside the machine. There are two hard disks in the screen FT-R3050 machine, and the information prompts the user which hard disk has a problem. When these messages appear, the user should check whether the connections of the hard disk are connected, initialize the hard disk, and check whether the control circuit board of the hard disk is damaged. Product categories of Cabinet Furniture, we have years of experience in the manufacture of furniture, Shoes Cabinet, Bedside Table, Cupboard , TV Stand and Coffee Table suppliers/factory, wholesale high-quality products of Study Desk , Gaming Desk and Working Desk . We have the perfect after-sales service and technical support. We hope we can cooperate happily.
Cabinet Furniture,Bathroom Cabinets,Kitchen Cabinet,Storage Cabinets Baklam , https://www.baklamjm.com
Introduction to Information Display of FT-R3050 Imagesetter's Operation Panel (Continued)