Only by paying attention to the links that affect the quality of printing can we print exquisite prints, increase the yield of finished products, reduce consumption and increase benefits, so that enterprises can remain invincible in the market competition. Here we mainly discuss several problems that are often encountered in production and are easily overlooked. 1. The color of the wire mesh The colors of the wire mesh are white, yellow, amber, red, etc., among which the yellow wire mesh is preferred. 270-280T yellow silk screen imported from Japan or Germany is commonly used in production. For particularly delicate printed products, we usually use 350T imported yellow screen. Why use yellow wire mesh? We know that the brilliant colors in nature are all due to the effect of light. Without light, there is no color. The color of light is determined by the frequency of light waves. Red, orange, yellow, green, blue, basket, and purple are the light that people's visual nerves can feel, called visible light. Different colors are obtained by the selective absorption and reflection of light on the surface of an object. In short, any color we can see is the color of light. That is, when a beam of light hits the surface of a yellow object, only the yellow light is reflected, stimulating our optic nerves to appear colored, and other colored light is absorbed, so we see the color of the object is yellow. Because screen printing uses ultraviolet light during exposure, purple light is a mixed reflection of cyan and magenta hues in color, that is, the lack of yellow hues in black. During the exposure, the yellow of the purple plus silk screen is superimposed into black, so the surface of the yellow silk screen (ie, the bottom of the emulsion layer) is not light-sensitive or lightly exposed, so there will be no "back exposure" phenomenon, and the resulting image has high definition , No vignetting. What is backfat? That is, when light passes through the transparent part of the film and reaches the emulsion layer, reflections, refractions, and slow shots are generated on the surface of the white screen located in the middle or bottom of the coating layer, which is just exposed from the bottom and inside of the coating surface. This phenomenon is called "back exposure". It will cause a virtual halo during exposure and affect the reproduction of tones. 2. Coating of photosensitive emulsion Put the prepared photosensitive liquid into the stainless steel tank, and the photosensitive liquid will occupy about half of the tank. The coating tank is in contact with the lower end of the inclined screen, and while the tank is inclined to flow out the photosensitive solution, the tank is slowly and uniformly lifted up to apply along the surface of the screen. The coating speed should not be too fast, too fast will cause blistering of the photosensitive emulsion, and pinholes will occur on the film surface; too slow will cause uneven coating of the photosensitive emulsion. In order to obtain the best coating effect, it is best to apply from the side that is in contact with the substrate when printing. The coating area should be slightly smaller than the screen frame, and then apply the screen upside down and apply again. After coating the reverse side of the screen, it is dried so that the photosensitive emulsion fills the mesh. It is best to use hot air drying at 30 ～ 35 ℃, which can shorten the drying time. If the temperature is higher than 40 ℃, the screen will produce hot fog. The sensitivity of the emulsion in the liquid stage is low, and the sensitivity increases with the drying of the coating film, and the specified sensitivity can be reached after complete drying. . Of course, due to the different production conditions of various manufacturers, their coating methods and times are also different. Since dust falling on the surface of the screen will cause pin holes in the screen, keep the room clean. At the same time, the poor treatment of the silk screen will also cause excessive pinning on the surface of the screen. When the photosensitive emulsion is applied, the drying place is too bright, which will cause the haze of the screen full-page image to affect the clarity and saturation of the printed matter. Reborn PLLA (poly-L-lactic acid) is a biodegradable synthetic material commonly used in cosmetic procedures to stimulate collagen production and improve the appearance of wrinkles and facial volume loss. Now Penis enlargement can be achieved with a minimally invasive injection of Reborn plla fillers. Injections can increase the girth of the penis while also increasing the length of the flaccid penis. Using Reborn PLLA Dermal Fillers for injection is preferred Penis enlargement can be achieved with a minimally invasive injection of dermal fillers. Injections can increase the girth of the penis while also increasing the length of the flaccid penis. Using fillers for injection is preferred.Reborn PLLA Filler is a natural collagen production filler. And Reborn plla is very safe for body beauty. Welcome to send inquiry to us for more details. Fillers For Penis Enlargement,Dermal Filler Penis Enlargement,Penile Injectable Fillers,Penile Enlargement Dermal Fillers Rimless Industry Co.,Ltd. , https://www.rebornplla.com
If you want to change your current status, Reborn plla will be a good choice.
Common problems in screen printing (1)
We take REBORN and RIMLESS as the core brands, biomedical materials and their applications in the medical field as the main business, and the high-end medical devices as the research and development direction.Such as Reborn PLLA Dermal Filler ,Reborn PLLA Hydrogel, PLLA,PLGA,PCL and other age related products and polymers,copolymers.
At present, our products have covered more than 60 countries and regions around the world, and we have established long-term and stable strategic partnerships with our customers of hospitals, distributors/dealers and doctors.
We can offer our customers OEM and private labeling services to create its own unique line. We are committed to extending the beauty business from the biomedical materials to medical devices, pharmaceuticals, plastic surgery, cosmetics and 3D printing, and give you our best service and products with our professionalism and enthusiasm.